The sketch for Try a Sketch on Tuesday's Challenge #690 inspired the design for my card. I basically followed the sketch to the letter, though I did substitute a leafy cluster for the smaller background hexagon.
I began with the cross panel. After I die cut the mat, using an Elizabeth Craft Designs "Stitched Indented Rectangle" die (discontinued), I die cut the panel from Canson XL mixed media paper with a Hero Arts "Rounded Rectangle Infinity" die to fit inside the mat. I determined the proportions of both parts of the cross, & cut 2 pieces of yellow Frog tape to those measurements. I lightly penciled the position for the tape pieces to center them on the panel, & adhered them on those marks. I made sure to burnish them well to the paper, as I did NOT want them to lift up & let ink underneath. (Spoiler alert: that happened.)
One of the palettes from Sarah Renae Clark's Color Cube system (old system version palette #342) inspired my ink color choices. For the ink blending around the cross, I took a cue from this image I found on Pinterest. I used a small ink blending brush to go around the whole cross with Tumbled Glass Distress ink to give me a base color. Then I added in bits of Peeled Paint, Stormy Sky, & Broken China Distress inks. After I had what I felt was a good balance of colors, I peeled off the tape masks. Unfortunately, ink had "leaked" under the tape in a few small spots, but that was nothing that a white gel pen couldn't cover up - shhhh! 😉 I adhered the main panel to the navy mat, & set that aside.
For the image hexagon, I used Deep Red's "Lily Blossom." This is a stamp that I have had for a loooong time! I don't use it that often, but it seemed perfect for this card. I stamped it onto Strathmore vellum bristol paper with Altenew's Vanilla Cream ink, then die cut it with a We R Makers "Nesting Hexagon" die (discontinued). I wanted a soft color, but not quite as pale as for "no-line" coloring. I used my Prismacolor colored pencils to color the leaves & add shading to the flower petals. To help it stand out a bit, I inked around the edges of the hexagon with Stormy Sky Distress ink.
I pulled out another oldie-but-goodie stamp - Stampabilities' "Happy Easter 2016" (discontinued) - for the greeting. I heat embossed it on another scrap of mixed media paper, & inked over it with Tumbled Glass Distress ink. I blended on some Stormy Sky to the bottom for an ombre effect. After I did that, I realized I may have made a bit of an error in judgment. When I fussy cut (as I was here), I like to outline the greeting or image lightly in pencil first, to give myself a guideline to cut on. (I picked up this tip from Kristina Werner.) But I was afraid that, when I went to erase any errant pencil marks I might have, I might erase the ink as well. After thinking about it for a moment, I decided to see if my Frixion heat-erasable pen would work. So I tried it on a section of the paper that I knew I would cut away, & it worked like a charm. All I had to do was hit it with my heat gun & the ink disappeared without leaving a trace. Whew! So I outlined the greeting with my pen (leaving a little extra room around the greeting than I normally would) & then cut just inside those lines. Even cutting inside the lines, I did have a few pen marks in the end I didn't cut off, so I just erased them with a shot of hot air.
I die cut the leaves from mixed media paper with the smaller die from Simon Says Stamp's "Etched Laurel Leaves" set. I wanted a soft green that kind of matched the leaf color I'd achieved in the lily image. It turned out Cracked Pistachio Distress ink was a good match, so I added some of that to my non-stick craft mat, spritzed with a bit of water, & ink smooshed the die cut leaves. I dried that with my heat gun, & repeated a couple more times for the depth of color I wanted.
Finally it was time to assemble the card. I found a piece of patterned paper in my collection that had a very faint (as in almost imperceptible) yellow check pattern. I cut that to the full 5x7" card size, & adhered that to my white card base. I adhered the matted cross panel next. I decided where exactly I wanted the hexagon, & used that to help me position the leaf cluster, which I tacked down with a few drops of glue, leaving the tips of the leaves free. I glued down the hexagon, & then the greeting. I had to add a few bits of cardstock behind parts of the greeting, since it overlapped the various layers & so wouldn't otherwise lie flat. I am so pleased with how this card came out! My mom will send it to a priest friend of hers, who I hope will like it just as much.
I'm also entering this card in the following challenges:
- Double Trouble Challenge #211: "In with the Old, Out with the New" (used old stamps for a new project) TSOT #690
- The Paper Funday Challenge #85: "Anything Goes" (not playing the optional twist)
- 613 Avenue Create March Challenge: "Anything Goes" (not playing the optional twist)
- Die Cut Divas March Challenge: "Celebrate Spring"
